Difference between revisions of "Astronaut OpenVistA on Ubuntu"

Revision as of 21:00, 3 February 2010

OpenVistA consists of two parts: a database server and a collection of client modules. The server runs in Linux. The CPRS clients are generally Windows-based (at this time), but the OpenVista-CIS client (a CPRS re-write by Medsphere) is available for both Windows and Linux (and perhaps Mac).

The first step is to install the OpenVistA server. It can be installed on the operating system of a stand-alone computer or on the guest operating system of a virtual machine (usually running on the same computer as the client modules).

When the VistA server is run within a virtual machine on the same computer as the client modules, a fully self-contained OpenVistA EHR is created on a single computer.

• If you will run the OpenVistA server on a standalone computer, then install the Ubuntu Server edition as an operating system on that computer first. (You can add an ubuntu-desktop or kubuntu-desktop GUI to the server later, if you so desire).

• If you will run the OpenVistA server within a virtual machine, then install the Ubuntu Server edition (virtual machine minimal install) into a virtual machine first. See these instructions.

Then proceed in a similar fashion (in each type of operating system installation) for the subsequent installation of Astronaut VistA.

Preparing your server

• The Astronaut installer uses an emerging standardized installation framework for VistA derivatives (WorldVistA and OpenVistA currently). These instruction reflect this framework, with modifications I have used in setting up my system on Ubuntu.

• Port 9260 is used for communications with the VistA server, which is tunnelled through an SSH tunnel using port 22. The VistA server should have a static IP address on your LAN, and your LAN should forward port 22 (and perhaps port 9260 during testing) traffic to that IP address on the LAN. Make sure your VistA server's firewall (if any) allows port 22 (and port 9260) traffic.

It is easiest to set this up before using the Astronaut installer, since the Astronaut server installer autodetects IP address settings.

Installation

Medsphere's OpenVistA uses one of the largest electronic health record platforms in the public domain. It is based on the US Veterans Administration health record system and is AGPL licensed. The database and server can be installed on a standalone server (which would then be accessed over a network by clients on other computers) or can be installed in a virtual machine on a computer which also contains the clients (creating a self-contained EHR on a single computer). There are several installation packages. The original OpenVistA site is here.

• Apache2 is required. It can be installed individually (sudo apt-get install apache2) or as part of a LAMP (Linux, Apache2, MySQL5, PHP) installation:

sudo tasksel install lamp-server

• The OpenSSH server is required:

sudo tasksel install openssh-server

• If you are installing on a Server edition without a desktop, you will also need:

sudo apt-get install wget iptables nano

• A beta .deb package called Astronaut OpenVistA EHR (for clinics) is available here. See the Astronaut website for additional installation instructions.

• Install prerequisites:

sudo apt-get install xinetd update-inetd whois apache2-suexec

• Astronaut VistA is made for a 32-bit operating system. If you are using a 64-bit Ubuntu operating system, then also install ia32-libs:

sudo apt-get ia32-libs

• Obtain and install Astronaut OpenVistA:

wget -O astronaut-ov-server-current.deb http://sourceforge.net/projects/astronaut/files/Astronaut%20OpenVistA%28tm%29%20Server/astronaut-ov-server-beta-0.9-3.deb/download
sudo dpkg -i astronaut-ov-server-current.deb

Note: It is recommended to install OpenVistA on a dedicated server. Apache and other server settings will be altered by the installation, which may alter your ability to run other servers on the same machine.

• Open incoming port 9260 in your firewall. If behind a router, make sure this port is forwarded to the IP address of the computer acting as the OpenVistA server.

• Note: This installation installs the OpenVistA database and server in an Ubuntu Linux OS (that resides either on a standalone computer or in a virtual machine). The CPRS user client for VistA is written in Delphi for Windows (and works imperfectly in Wine). The CPRS client is therefore usually installed onto a Windows-based PCs (or onto USB flashdrives). These CPRS clients connect through the network to the OpenVistA server on a Ubuntu Linux-based server PC, or directly to the virtual machine.

• Also see the YouTube video.

Installing on a Server edition

If you are installing on a Server edition without a desktop/package manager installed, you may need to install as root:

sudo -s
sudo dpkg -i astronaut-ov-server-current.deb
sudo apt-get -f install

Note: The command "apt-get -f install" finds and installs unmet dependencies. This is only needed for Server editions in which a package manager is not installed.

Installing OpenVistA Server in a Virtual Machine

• Install the Ubuntu Server edition (virtual machine minimal install) into a virtual machine (like VirtualBox) and then install Astronaut OpenVistA on top of this. See these instructions.

Use a static IP address for the server

It will be difficult for the VistA clients to locate the OpenVistA server if the IP address of the server is always changing (i.e. repeatedly assigned a new dynamic IP address by the router/network DHCP server). It is best, therefore, to assign a static IP address to the server.

The network administrator must assign the static IP address on the LAN for use by the server (especially if a DNS nameserver is in use on the network). Let's say the LAN has a router/gateway address of 192.168.1.1, a static IP address range of 192.168.1.125 - 192.168.1.253, and the server is assigned an IP address of 192.168.1.135. Then the Ubuntu Server can be configured to use this static IP address.

• When the Ubuntu Server OS is running, edit the /etc/network/interfaces configuration file:

sudo nano /etc/network/interfaces

• Make sure the settings are similar to:

# The loopback network interface
auto lo
iface lo inet loopback
#
# The primary network interface
auto eth0
#iface eth0 inet dhcp
#
iface eth0 inet static
address 192.168.1.135
broadcast 192.168.1.255
netmask 255.255.255.0
gateway 192.168.1.1

• Reboot the Ubuntu OS again so that the new IP address is used.

sudo reboot

Connect with a CPRS client

• See the Astronaut CPRS client package installation and configuration instructions. This package uses the TMG-CPRS client as well as other standardized clients which can be used interchangeably with either WorldVistA or OpenVistA.

• Also see the Medsphere OpenVista-CIS client package, which is a modification of CPRS with image viewing and other commercial ehancements. It can be used with the Astronaut OpenVistA server along with the Astronaut client package listed above.

Using the VistA Configuration Utility

• See the VistA Configuration Utility usage instructions.

Using the VistA Clinical Scheduling utility

The Clinical Scheduler from the Indian Health System's RPMS system has been imported as one of the modules included with an Astronaut VistA installation.

• See the VistA Clinical Scheduling Utility usage instructions.

Configure access to the VistA server from the Internet through a virtual server

• See Ubuntu Virtual Servers

Other resources